Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHinge & Post Repair in Brooklyn, NY
A sagging gate in Brooklyn usually comes down to two things: a hinge that has pulled loose or a post that has shifted. Hinge and post repair means resetting the hardware and structure that carry the gate’s weight, so it swings cleanly and closes the way it should. At Latch and Post Gate Repair Brooklyn, this is the work we do most weeks across neighborhoods like Park Slope, Bay Ridge, Bedford-Stuyvesant, and Marine Park. If your gate drags on the sidewalk or the latch no longer lines up, call us at (934) 649-3673 and we’ll give you a straight answer on what it will take to fix it.
Every gate comes down to two parts: the latch that holds it and the post that carries it. That’s the job we focus on as part of our broader Gate Repair service. When the post leans and the hinge fails along with it, the gate stops being a gate. It becomes a daily annoyance and, left alone, a bigger repair. We’d rather catch it before that happens.
When You Need Hinge & Post Repair
Most hinge and post problems announce themselves slowly. A gate that rubs the ground in July may have been warning you since March. Here are the signs Brooklyn homeowners call us about:
- The gate drags or scrapes when opening or closing. This is usually a sagging hinge, a leaning post, or both. In older brownstones and prewar rowhouses, brick gate posts shift over decades, and the hinge takes the strain first.
- The latch no longer lines up with the strike plate. When a post leans even a few degrees, the latch misses its target. You’ll find yourself lifting the gate to make it catch, which works until it doesn’t.
- Visible rust or corrosion at the hinge pins. Brooklyn’s salt air and wet winters are hard on steel hardware. A rusted hinge pin binds, squeals, and eventually snaps, which drops the full weight of the gate onto the remaining hinges and the post.
- The gate leans noticeably to one side. A post that tilts outward changes the gate’s geometry. On Mighty Mule and LiftMaster automated gates, this misalignment triggers the auto-reverse or causes the opener to strain, shortening its life.
- A hinge has pulled free of the post or the gate frame. Wood posts rot around the screw holes. Concrete and brick posts crack under repeated stress. Either way, tightening the same screws won’t hold, and the next step is a proper repair, not a bigger screw.
- The gate bounces or shakes when it closes. Loose hinges let the gate flex. Over time that flex widens the hinge mortises and damages the post, which turns a $200 hardware fix into a $900 post replacement.
Our Hinge & Post Repair Process
We follow a set routine on every hinge and post call in Brooklyn. It’s the same routine we’ve used since 2009 under the Cedarwell family of gate specialists, and it keeps surprises off the bill and dirt off your floors.
- We inspect the full gate: posts, hinges, latch, and the surrounding ground. Frost heave in Brooklyn winters shifts posts, and drainage problems soften the soil around them. We look at the whole picture before touching anything.
- We explain what we found and hand you a written price. You’ll see the number before any work begins. No pressure, no “while we’re here” add-ons. If it’s a $240 hinge replacement, you’ll know that’s what you’re paying.
- We reset or replace the hinge hardware. For gates on brands like FAAC, BFT, and LiftMaster, we use hardware matched to the gate panel’s weight and the post material. A steel post gets different treatment than a cedar post or a brick pier.
- We correct the post alignment. That may mean resetting a concrete footing, reinforcing the existing post, or in severe cases replacing it. We level and brace, then check the swing at three points: fully open, halfway, and closed.
- We test the latch, the auto-close, and the opener’s force settings where one is installed. A gate that closes correctly by hand should close correctly on a BFT or Ghost Controls opener too. We test both.
- We clean the work area, photograph it, and walk you through everything we did. Shoe covers and drop cloths are included on every visit, and we take a photo of the cleanup before we leave. That’s part of the Cedarwell Care Promise, not an add-on.
Hinge & Post Repair Pricing in Brooklyn
What you’ll pay depends on three things: the condition of the post, the type and number of hinges, and whether an opener is involved. Here’s the honest range based on the work we’ve done across Brooklyn:
- Standard hinge replacement (1-2 hinges, steel or aluminum): $180 to $320, including hardware and labor.
- Heavy-duty hinge replacement on a steel or iron gate: $300 to $520, depending on gate weight and hinge size.
- Post reinforcement (concrete or steel post, still structurally sound): $250 to $480, including alignment and hardware.
- Full wood post replacement with concrete footing: $600 to $1,050, including demolition, new post, and concrete work.
- Brick post repair with repointing around the hinge area: $350 to $750, depending on the extent of the masonry work needed.
Gates with automatic openers add a small amount of labor for lock and opener re-alignment after the hinge and post work, usually $80 to $160. We’ll tell you before we do it, and you’ll have the number in writing before we begin. Estimates are free, and the quote you get is the price you’ll pay under our 365-Day Done Right Promise. If the repair isn’t right, we make it right, no argument, no fine print.
Post Types We See in Brooklyn
Brooklyn gates hang on three main post types, and each fails a little differently. Knowing which one you have helps explain what the repair involves.
Wood posts, especially cedar. Common in brownstone yards and rowhouse front gates from Bed-Stuy to Windsor Terrace. They rot at ground level where the post meets the soil, and the hinge screws lose purchase. When we replace a cedar post, we set the new one in concrete and wrap the buried portion in a moisture barrier so the next person doesn’t face the same failure in five years.
Steel posts set in concrete. Typical in newer construction and commercial-facing gates. Steel posts usually fail at the weld points or the base plate, not the post itself. We inspect the base welds on every call, because a hairline crack there is the difference between a $300 repair and a post that snaps on a windy day.
Brick or masonry piers. Found on older Park Slope and Brooklyn Heights properties. The hinge side of a brick pier takes concentrated stress over decades, and the mortar joints begin to crumble. Repair means removing the loose brick, reinforcing the anchor points, and repointing the area around the hinge plate.
Automated Gate Hinges: A Word on Adjustments
Hinge work on an automated gate carries an extra step people don’t always expect. When a LiftMaster or Mighty Mule opener has been compensating for a sagging gate, its open and close limits are wrong. Once we fix the hinge or post, the gate swings differently, and the opener needs its travel limits reset to match. We do that as part of the job on every hinge and post repair where an opener is involved, and we test the force settings so the gate doesn’t push against anything it shouldn’t. If you have pets, a gate that closes too hard can spook them or worse. We set the force low enough to reverse on contact, as the opener manufacturer specifies.
Why the Post Matters More Than the Hinge
People call about a hinge and we often find the post is the real problem. A hinge is a mechanical part, easy to swap. A leaning or rotted post is a structural one. Until the post is right, any new hinge is just borrowing time. We fix both, and we don’t charge you for work the post doesn’t need. If the post is solid and the hinge failed on its own, you’ll only pay for the hinge. That’s the kind of answer you get when a live person answers the phone at (934) 649-3673, day or night, and a technician who actually looked at your gate gives you the truth.
FAQs – Hinge & Post Repair
How much does hinge and post repair cost in Brooklyn?
Most hinge and post repairs in Brooklyn run between $180 and $1,050, depending on whether the hinge alone is failing or the post needs replacement. A standard hinge swap costs $180 to $320, while a full wood post replacement with new concrete runs $600 to $1,050. Call (934) 649-3673 for an exact quote, estimates are free and you’ll get the number in writing before we start.
Is it cheaper to repair a leaning gate post or replace it?
Repairing a leaning post usually costs less than replacing it, often $250 to $480 compared to $600 to $1,050 for a full replacement. If the post is structurally sound and only the footing has shifted, we can reset and reinforce it. If the post is rotted or cracked through, replacement is the honest call, and we’ll show you why with photos before any work begins.
Can you fix a sagging gate the same day?
In most cases, yes. Hinge replacements and simple post adjustments are typically completed in one visit. If the post needs a new concrete footing, the job may require a second visit to allow the concrete to cure before the gate is re-hung. Call (934) 649-3673 and we’ll tell you which situation you’re in based on what you describe.
Will fixing my gate hinges affect my automatic opener?
Yes, and we handle that as part of the repair. When a LiftMaster, FAAC, BFT, or Mighty Mule opener has been running on a misaligned gate, its travel limits and force settings need to be reset after the hinge or post work is done. We include the opener re-alignment in the repair quote, so your gate closes smoothly and reverses safely if something is in the way, a child, a pet, a trash bin.
Do you work on all gate brands in Brooklyn?
We service hinges and posts on gates fitted with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule openers. The hinge and post work itself applies to any gate, but if an opener is involved, these are the systems our technicians are factory-trained to adjust. If your gate has an opener from a brand outside this list, call us and we’ll tell you straight whether we can help.
Call Latch and Post Gate Repair Brooklyn
A gate that doesn’t close properly stops being a convenience and starts being a hazard, to your kids, your pets, and anyone who walks past. We answer the phone around the clock, we show up when we say we will, and we treat your floors and your time the way we’d want ours treated. Our technicians are background-checked, uniformed, and working under the Cedarwell C.A.R.E. values: Clean up like it’s our own home, Ask before we move or touch anything, Respect your family’s time and quiet hours, Explain the price before the work. For hinge and post repair anywhere in Brooklyn, call (934) 649-3673 for a free estimate.
Written by Cody Beckman, Owner at Latch and Post Gate Repair Brooklyn, serving Brooklyn.